STANDARD FEATURES

• Pannasonic or Mitsubishi PLC Program Control.
• Short PCB cycle time.
• Thin PCB cabability.
• Uninterrupted PCB charging.
• Pre-warning low stack sensor.
• Towerlight display for machine status.
• Smooth and parallel width ajustment (lead screw)
• By-pass mode selectable without removing PCB stack.
• SMEMA compatible.

STANDARD FEATURES

• Pannasonic PLC Program Control.
• Selectable pitch settings.
• Towerlight display for machine status.
• Automatic magazine-change over.
• Flexible platform to suite standar magazines.
• Regulated pressure on attached pneumatic pusher.
• Pusher position ajustable to centre of the magazine.
• User friendly «soft touch screen» membrane control panel.
• Automatic magazine alignment by upper and lower pneumatic clamping.
• SMEMA compatible.

STANDARD FEATURES

• Pannasonic PLC Program Control.
• Locking cilynder to avoide opening during PCB transfer.
• Ergonomic air pressure supported opening and closing.
• Automatically gate lifting down by push button.
• Somoth and parallel width ajustment (lead screw)
• SMEMA compatible.

STANDARD FEATURES

• Modular design, PLC controlled.
• Stability enhanced by heavy design.
• Ergonomic design arm rest.
• Smooth and parallel width adjustment (stainless steel screws).
• Different lengths available upon request.
• Multi-segment concept available upon request.
• Automatic/Manual modes.
• Independent variable speed controls for each rail.
• Independent inspection buttons.
• SMEMA compatible.
• CE certificates.

STANDARD FEATURES

• Sturdy and stable design.
• High quality ESD conveyor belt for longest lifetime, easy to replace.
• User friendly “touch panel” control panel and PLC controller.
• Reject, inspect and pass through models.
• Speed adjustable by software.
• Standard automatically stack up 5 NG PCBs.
• Conveyor length could be customer made.
• Special guiding mechanism installed at the entrance and exit of this unit for smoothest operation.
• Smooth and parallel width adjustment.
• SMEMA compatible.
• 2 years warranties for all parts.
• CE certificates.

STANDARD FEATURES

• PCB size: 80 x 50 ~ 510 x 460mm.
• PLC control + Omron sensors.
• Diameter: 3mm edge round belt.
• Air Pressure: 5kgf/cm2.
• Power: AC220V, 50/60 HZ, 1 phase.
• PCB Convey Direction: L-R ( Or R-L).
• Front rail fixed ( or rear rail fixed).
• Conveyor Height:900+/-50mm.
• Conveyor Speed: 10m/s.
• Built-in rotary mechanism to ensure highest level of safety.
• Sturdy and stable design.
• User friendly “touch panel” control panel.
• Smooth and precise rotation.
• Smooth and parallel width adjustment.
• SMEMA compatible.
• CE certificates.

STANDARD FEATURES

• Touch screen with user-friendly control mode and English language.
• Good or bad board separation.
• Multi function sound and signal light alarm tower.
• Conveyor width adjustment using hand wheel.
• Panasonic or Mitsubishi PLC control + OMRON sensors.
• Pitch selectable: 10.20.30.40mm pitch or specify.
• PCB components space available: up 30mm, down 20mm.
• Magazine racks capacity: top one and down two magazine.
• Automatic motorized pusher to protect the safety transfer the PCB into the magazine.
• Magazine rack 50 slots · Self diagnostic Error Code display.
• AirTec pneumatic clamps to secure magazine rack pressure regulated.
• Flexible platform to suit standard magazines.
• Regulated pressure on attached pneumatic .
• Pusher position adjustable to center of the magazine.
• Automatic magazine alignment by upper and lower pneumatic clamping.
• SMEMA compatible.

STANDARD FEATURES

• Pannasonic or Mitsubishi PLC Program Control.
• Selectable pitch settings.
• Towerlight display for machine status.
• Automatic magazine change-over.
• Flexible platform to suit standard magazines.
• Conveyor width adjustment using hand crank.
• Regulated pressure on attached pneumatic pusher.
• Pusher position ajustable to centre of the magazine.
• User friendly «soft touch screen» membrane control panel.
• SMEMA compatible.